How To Straighten Bent Rv Awning Arm

To straighten a bent RV awning arm, first remove the arm from the bracket. Make sure to keep track of any screws or fasteners that may have been holding it in place. Lay the arm flat on a hard surface and use two pieces of wooden scrap material to press against both sides of the bend.

Use clamps to secure them in place and apply pressure until you feel the bend start to become less noticeable. Take your time with this process as applying too much pressure can cause further damage. Once complete, reattach it back into its original location using any previously removed fasteners or screws and test out your work by opening up the RV’s awning!

  • Locate the bent arm: Inspect the rv awning carefully to identify the location of the bent arm.
  • Remove Awning Arms: Remove all arms from the RV awning before attempting to straighten them out. This will help ensure that any movement done on one arm does not affect another one and make matters worse.
  • Use Leverage: Place one end of an adjustable wrench against the bottom section of the bent arm, and place its other end against something stationary such as a fence post or tree trunk for leverage (if outdoors). Pull up on it slowly but firmly until you can feel resistance, then stop pushing and allow your body weight to do most of the work in straightening out the bend in an even manner without applying too much force at once which could cause damage instead of repair
  • Check Alignment: Once you have finished using leverage to straighten out your RV’s awning arms, check their alignment with each other again just to make sure everything is back where it should be before reattaching them back onto your vehicle’s frame or wall mountings

Why is My Rv Awning Crooked?

If you’re noticing that your RV awning is crooked, it could be caused by several different factors. Firstly, sometimes the fabric of an awning can become stretched over time, resulting in a drooping appearance. This isn’t uncommon and can be remedied with some simple maintenance.

If this isn’t the case however, then it’s possible that the mounting brackets or hardware may have loosened due to vibration from travelling on rough roads. Check these components for any signs of wear and tear and tighten them if necessary – you might need to use some thread-locker glue for extra security.

Finally, make sure all the arms are at equal lengths so they open evenly when deployed – if one arm is shorter than the others then this will cause an uneven pull which will result in a crooked appearance once opened fully. With regular maintenance and care, you should hopefully find that your RV awning remains perfectly straight!

How Much Does It Cost to Replace Awning Arm on Rv?

Replacing an awning arm on your RV can be costly, depending on the type and size of the RV. The cost will vary widely depending on whether you do it yourself or hire a professional to do it for you. If you are going to replace the arm yourself, then it is important to make sure that you have all of the necessary tools and parts before beginning the project.

Depending on what type of arm needs to be replaced, you may need various types of nuts, bolts and screws in order to complete this job properly. Additionally, if there’s any damage caused by rust or corrosion then even more parts may be needed which can add up significantly when purchasing them from an RV repair shop or online store. Furthermore, if your RV has special features like power arms that require electronic motors connected with wiring harnesses and switches – these will likely drive up costs as well due to their complexity and additional labor required for installation.

On average though, replacing one awning arm can range anywhere from $50-$250 dollars depending on how much work is involved in removing/installing components correctly without damaging other areas such as siding panels or windows nearby.

How Do You Straighten a Bent Awning Tube?

If you have an awning with a bent tube, don’t worry–it can be fixed! In most cases, the tube will need to be straightened by hand. To do this, start by loosening any screws or bolts that hold the fabric in place so that it is taut and can move freely.

Then, use your hands to carefully bend the tube back into its original shape. If you encounter any resistance while doing this, stop and make sure you aren’t going too far as overextending the metal could cause further damage. Once it is properly aligned again secure the fabric back to its frame using whatever fasteners were previously used before testing it out for proper tension.

With careful attention and some patience, you should now have your bent awning tube looking good as new!

How Much Does It Cost to Replace an Awning Arm?

Replacing an awning arm can be quite expensive depending on the type of material you choose and its size. Depending on the make and model, it usually costs anywhere between $200-$400 to replace just one arm. This cost does not include labor fees or any additional materials that may be required for installation.

If your awning is made out of hard-wearing fabric such as vinyl or canvas, then replacing the entire cover might be more economical than just replacing one arm. It’s important to remember that when replacing an awning arm, professional help is highly recommended since this job requires specific tools and expertise in order to ensure proper installation.

Additionally, if you are installing new arms yourself it could void any warranties associated with your existing setup so seek advice from an experienced installer before making changes to your system.

How to Adjust Rv Awning for Rain

To adjust your RV awning for rain, first make sure that the arms of the awning are fully extended and locked in place. Next, pull down on the tension knobs located at each end of the awning until it is tight. You may need to add additional tension by pulling down further or using weights such as rocks or bricks to hold it in place.

Finally, check all seams and corners to ensure that they are securely fastened so there is no water leakage when it rains.

Common Rv Awning Problems

One of the most common issues that RV owners face is awning problems. The awning can become damaged due to weather conditions, or simply age and wear and tear. If your RV’s awning is not properly maintained it can easily become torn, cracked, faded or show signs of mold and mildew growth.

Additionally, the wind may cause the fabric to stretch out which will weaken its overall strength. It’s important to inspect your awning regularly in order to identify any potential issues before they worsen and require more extensive repairs down the line.

Retractable Awning Arm Repair

Retractable awning arm repairs are relatively simple and can often be done without the help of a professional. The most common repair involves replacing corroded or damaged arms with new ones, and adjusting tension on the cables that control opening and closing. It is important to use the correct tools for any retractable awning arm repair in order to ensure proper operation.

Additionally, it may also be necessary to lubricate moving parts with silicone spray or other suitable products in order to maintain smooth movement and minimize wear over time.


In conclusion, straightening a bent RV awning arm is a relatively simple process. First, inspect the arm and identify any damage that may have occurred during the bending process. Next, remove the arms from their mounting points by removing screws or bolts.

Then carefully apply heat to both ends of the metal arm with an electric heating pad until it is malleable enough for you to bend it back into its original shape. Finally, reattach the arms to their mounting points and secure them in place with screws or bolts before testing out your new RV awning arm! With these steps in mind, anyone can easily restore their bent RV awning arms without needing professional assistance.

Leave a Comment