Fleck 5600Sxt Flow Meter Not Working

The fleck 5600sxt flow meter may stop working if it becomes clogged or damaged. Troubleshoot the issue by checking the flow meter’s wiring and cleaning or replacing the meter, if necessary.

The fleck 5600sxt flow meter is responsible for measuring the amount of water passing through the system and controlling the regeneration cycle. When the flow meter stops working, it can cause the system to malfunction and affect the quality of water being produced.

The most common causes for a flow meter failure are damage and clogging. To troubleshoot the issue, check the wiring connections and make sure they are secure. Then, clean the flow meter with a soft-bristle brush and gentle detergent to remove any buildup. If cleaning does not work, replace the flow meter to get the system back up and running correctly.

Causes Of Fleck 5600Sxt Flow Meter Not Working

Are you experiencing problems with the fleck 5600sxt flow meter not working? This type of issue can be frustrating, but there are several reasons why it could be happening. In this blog post, we’ll discuss both internal and external causes that can affect the flow meter’s functioning.

Discuss Internal Causes

Internal causes of a fleck 5600sxt flow meter not working can vary from clogging, damage or calibration issues.

  • Clogging: any minerals or debris can cause the flow meter to stop functioning correctly if it becomes clogged.
  • Damage: any physical harm, especially to the impeller blades, can prevent the flow meter from working.
  • Calibration issues: if the calibration has been disrupted for any reason, the flow meter might provide an incorrect reading.

Discuss External Causes

There are external causes to fleck 5600sxt flow meter not working, as well. These can include power issues, installation errors, and water flow regulation problems.

  • Power supply: if the meter isn’t getting an adequate power supply, it may not operate properly.
  • Installation errors: if the meter was installed incorrectly, it could impact its accuracy and performance over time.
  • Water flow regulation: any problems that involve the water flow rate, such as changes to pipe size or pressure, can cause problems with the flow meter’s functioning.

Correctly diagnosing the issue with fleck 5600sxt flow meter can be a challenge, but carefully considering the internal and external causes can help solve the problem. With these helpful tips, you’ll have all the information you need to get your flow meter working correctly again.

Symptoms Of Fleck 5600Sxt Flow Meter Not Working

Are you experiencing issues with your fleck 5600sxt flow meter? A faulty flow meter can adversely affect your water treatment system’s performance, leading to a wide variety of problems. In this section, we’ll discuss the common signs and symptoms of a fleck 5600sxt flow meter not working.

By understanding these indications, you can quickly identify the problem and take the right steps to get it fixed.

List The Common Signs Of Faulty Flow Meter

Here are some of the most common signs that your fleck 5600sxt flow meter might not be working correctly:

  • Reduced water pressure: if you notice that your water pressure has decreased, it could be due to a malfunctioning flow meter.
  • Irregular water softening: if you’re not getting the expected level of water softening, it’s possible that your flow meter is not working correctly.
  • Inaccurate water usage readings: if you notice that your water usage readings are not displaying properly or are not consistent with your actual usage, there could be an issue with your flow meter.

Explain How These Signs May Indicate Other Issues With The Water Treatment System

While these are all signs that your flow meter might not be functioning correctly, they could also point to other issues with your water treatment system.

  • Reduced water pressure: it could be a sign that there is a blockage or clog in your water system that’s preventing proper flow.
  • Irregular water softening: it could be due to problems with the resin beads, motor, or other components of the system.
  • Inaccurate water usage readings: it could be due to factors like water leaks or damaged pipes, which can impact your system’s overall efficiency.

By understanding these potential underlying problems, you can take the steps needed to properly diagnose and fix issues with your water treatment system.

Keep an eye out for these common signs and indicators of issues with your fleck 5600sxt flow meter. If you notice any of these indications, make sure to investigate the cause and address it promptly. Getting your water treatment system back up and running smoothly can help preserve its longevity and protect the quality of your water for years to come.

Solutions To Fleck 5600Sxt Flow Meter Not Working

If your fleck 5600sxt flow meter is not working, there are several possible causes and solutions to the problem. As a homeowner or plumber, you must be aware of these issues and have the necessary skills or knowledge to fix them.

In this section, we will provide step-by-step procedures for troubleshooting and fixing the flow meter, depending on the underlying cause. We will also highlight preventive measures that can help prevent or minimize flow meter malfunction, including periodic maintenance, proper installation, and avoiding water flow overloads.

Troubleshooting And Fixing The Flow Meter Depending On The Underlying Cause

  • Check power supply: first, check the power source for the meter. If the meter is not receiving power, then it won’t work. Look for tripped breakers or power outages and switch them back on.
  • Inspect wiring and connections: if the power supply is okay, then check the wiring and flow meter connections. A loose or corroded wire or connection, or a damaged cable or plug can cause faulty readings or complete meter failure. Carefully inspect the wiring, connections and plug terminations and make sure they are clean and secure.
  • Test the paddle wheel and impeller: the rotating parts of the flow meter may be clogged with debris, preventing it from turning normally. Remove the paddle wheel or impeller from the meter, clean it, and reassemble it properly. Check if it moves freely and smoothly. Test the flow meter again to see if the reading is normal.
  • Replace damaged parts: if you can’t identify the cause of the problem, then some parts, such as bearings, gaskets, or sensors, may be worn out or damaged. Order and install new parts according to the manufacturer’s instructions.

Highlight Preventive Measures That Can Help Prevent Or Minimize Flow Meter Malfunction, Including Periodic Maintenance, Proper Installation, And Avoiding Water Flow Overloads.

  • Schedule regular maintenance: schedule regular checkups of the flow meter system. Check for any unusual pressure drops or leaks and inspect the wiring and connections. Follow the manufacturer’s maintenance schedule and recommendations.
  • Proper installation: ensure that the flow meter is installed correctly and that the piping is straight and clear of debris. Avoid installations in areas with high temperatures, vibrations, or corrosive chemicals.
  • Avoid overloads: avoid overloading the flow meter with excessive water flow rates. Use appropriate piping and valves for the flow rate and capacity. Use a bypass valve to divert water around the meter when needed.

By following these procedures and preventive measures, your fleck 5600sxt flow meter will work effectively and efficiently, saving you money and headaches in the long run.


In order to ensure that your water softener system is functioning properly, it is important to keep an eye on the flow meter. The fleck 5600sxt flow meter is one of the key components in the system, and if it is not working properly it can cause problems with the softening process.

As discussed in this blog post, there are several potential reasons why the flow meter may not be working, including blockages, mechanical issues, or problems with the wiring. It is important to troubleshoot the problem and address any issues promptly in order to avoid further problems with the system.

Whether you choose to tackle the problem on your own or seek professional assistance, it is important to be proactive when it comes to maintaining your water softener system. By doing so, you can prolong the life of your system, ensure that your water is safe and clean, and avoid costly repairs down the line.

So if you notice any issues with your flow meter, don’t hesitate – take action and get your system back in working order as soon as possible.

Leave a Comment